BCD Cressi START
If you’re looking for a durable, strong and almost bulletproof BCD jacket than the Start is what you are looking for. Constructed from extremely Strong 500 and 1000-Denier Cordura, with excellent buoyancy, even on smaller sizes the Start full jacket BCD fits the bill. Designed with the demanding use of dive training and rental facilities in mind this BCD will give the sport diver years of dependable use.
The BCD has three over-pressure relief/dump valves with two located on the left and right shoulders and a third lower valve on the rear right of the air cell. All three can be manually dumped two with pull cords and the other with the power inflator mechanism. There are two plastic D-rings and two additional snap hooks for attachment of instruments and accessories. If used at dive facilities a size indicator is highly visible on the right shoulder.
BCD has two large accessory storage pockets with hook and loop closures, and the adjustable sternum straps along with both torso adjustment and waist straps are equipped with squeeze-style” side-release buckles for easy donning and doffing. The waist strap/cummerbund assembly is independently suspended from the air cell allowing the air cell to inflate away from the diver preventing the squeeze-effect” when inflated. The backpack is rigid for support and stability of the cylinder yet is fully padded for comfort. The Cressi Start BCD come with a 3/8″ threaded quick-disconnect low-pressure hose and owner’s manual.
Buoyancy in: lbs. / kg / size
29.2 lbs. / 13.3 kg / XS
31.5 lbs. / 14.3 kg / S
33.7 lbs. / 15.3 kg / M
38.1 lbs. /17.3 kg / L
44.9 lbs. / 20.4 kg /XL
Designed Primarily as Rental BC for Resorts and Dive Schools
Strong Enough to Rent Bullet-Proof Construction for Recreational Divers
Stability of a Jacket Style BC
Cressi Start BCD Features:
- Material: 1000 denier Cordura Colorlock
Cordura 1000 Denier on the outside panel and 500 Denier on the inside. Cordura is more resistant to erosion caused by long-term friction and extends the duration of the weldings, as it is harder than Nylon. This is especially important for dive centers where the jackets are often inflated to their maximum capacity
- Large, Easily-Seen Size Markings on Shoulder
- Size shown on right shoulder pad.
- Size indicator clearly visible on the shoulder strap
Size shown on the shoulder pad. It allows a better management of the stock of school equipment and rental in diving centers.
- 2″ (50 mm) Torso Adjustable Shoulder Straps
- D rings located at the shoulders and two more front side rings.
- Quick-Release adjustable Buckle
Axillary Straps: Comfortable unisex design, leaving the chest area completely free. Fastex 40mm axillary buckles
- 3/8″ Threaded Low-Pressure Hose
- Rear Kidney and Right Shoulder Over-Pressure Relief/Pull Dumps
- Inflator Integrated Cable Activated Pull Dump
Inflator with double air filtration system; under the hose connection stem and around the valve. Easily disassembled for small cleaning operations, even at the beach (sand infiltration, etc)
Reinforced anchoring flap for inflator hose
- The pressure gauge and octopus anchoring systems are integrated, which is especially useful for dive centers
Integrated pressure gauge compartment
Integrated octopus compartment
REGULATOR AmScuD RX20
AmScuD’s RX Second Stage and RX20 PRO First Stage produce a low-priced, no-frills regulator system that offers easy breathing. This regulator is so rugged and economical to maintain (replacement parts are inexpensive) that it’s become popular as a rental. It can be used with air or nitro mixtures up to 40 % right out of the box.
The RX20 PRO lightweight material and anatomically designed mouthpiece translates into a second stage that won’t cause jaw fatigue. The RX20 PRO second stage is a dependable downstream demand valve design. It is also complete with DIVE AND PREDIVE knob for
The RX20 PRO First Stage Regulator offers all divers the opportunity to own a top performing regulator. Repeatedly rated as the best in its class, the RX20 PRO exceeds both Navy Class A and European CE standards. The RX20 PRO is a non-balanced flow-by piston designed regulator. This simple yet fail-safe design will deliver air even if there is a first stage failure. Made of marine grade chromed brass for durability and long life, the ZX10 first stage has 4 LP ports and 1 HP port with 3/8″ and 7/16″ threads. The Regulator weighs 26 oz. (737 1 g) and comes with a 30″ (76 2 cm) 3/8″ threaded low pressure hose.
Features:
- Rugged and Economical Design
- Popular as a Rental Regulator
- Proven Cost Effective to Maintain
- Nitrox Ready Up to 40%
- Total Weight: 32 oz. (900 g)
- Hose Length: 30″ (76.2 cm)
- Hose Thread: 3/8″
- Owner’s Manual
- First Stage: RX20 PRO
- Non-Balanced Flow-By Piston Design
- Fail-Safe Valve Design
- 4 LP Ports 3/8″ Thread
- 1 HP Port 7/16″ Thread
- 2’nd Stage LITE
- Dependable Downstream Demand Vale Design
- Lightweight ABS/Polycarbonate Housing
- Compact Design 2.9″ (7 cm) in Diameter
- Anatomical Mouthpiece for Reduced Jaw Fatigue
Octopus Cressi XS Compact
The XS Compact Second-Stage housing is made of durable non-corrosive hi-tech polymers, and has a dependable downstream demand valve mechanism with a lever that has a low coefficient of friction. The flow of air is channeled to the mouthpiece by injection, creating a venturi effect enhancing the performance. The 2’nd stage comes with a flow deviator that acts on the Venturi effect, with dive/pre-dive adjustment function. Large soft purge cover allows easy clearing of 2’nd stage and a comfortable silicone mouthpiece. The XS Compact Regulator weighs 4.76 oz. (135 g) without the hose, comes with a long 39″ (100 cm) 3/8″ hose, and owners manual. Octopus is in compliance with EN 250:2014 standard.
Cressi XS Compact Octopus Features:
- Cressi XS Compact Octopus
- Reliable Downstream Demand Valve
- Large Soft Purge Cover
- Venturi Dive/Pre-Dive Switch: Prevent Free-Flow when Not in Use
- Yellow Front Cover for Easy Identification in an Out-of-Air-Emergency
- Housing: Durable Non-Corrosive Hi-Tech Polymers
- Comfortable Mouthpiece
- Weight: w/o Hose 4.76 oz. (135 g)
- Hose Length: 39″ (100 cm)
- 3/8″ Thread Hose
- Owner’s Manual
Cressi XS Compact Octopus Specifications:
Adjustable 2’nd Stage
Yes, Venturi Pre-Dive/Dive Switch
2’nd Stage Type
Downstream Demand Valve
Materials
Housing; Polymers, Diaphragm and Mouthpiece; Silicone
Hose Thread
3/8″
Hose Length
39″ (100 cm)
Total Weight
4.76 oz. (135 g), w/o Hose
Console AmScuD XP2
All AmScuD instruments give a very accurate, clear visibility readings and are made from the best quality materials.
As such, we stand behind our products to give the utmost user experience.
Learning from our over 18 years in the industry, we have sucesfully established both design and materials that is a balanced of functionality, excellent robustness while maintaining a certain cosmetic estathic.
Did we tell you that our gauges are 100% Made in Italy? And it is backed by a full 1-year warranty.
The AmScuD submersible pressure gauge combined with depth gauge and compass, with an internal Bourdon pressure measuring mechanism, gives you clear information on the gas contents of your cylinder.
Dial range is stated in metric standard (BAR) from zero to 400 Bar while the depth gauge will show a METER unit with 1 meter increments.
Dial face is designed with ultra-clarity in mind by being uncluttered, with large black figures on a luminous background giving a long phosphorescent effect. We also include color-indicator for a better idea of what states you are in.
This makes viewing as easy as possible, even in poor visibility conditions.
- Our gauge case is made from nickel plated brass
- The dial window is made of highly shock resistant material (anti-splinter polycarbonate). 400 BAR/5,800 PSI dial gauge for your mission critical applications.
- Elasto-Polimer housing to ensure reliability while maintaining its function and esthathics.
- Over-pressure capsule fitted in the back of the module to prevent the screen from exploding in the unlikely event of the internal mechanism failing.
- Our exclusive Dual-Recoil® system located both in depth and pressure gauge. Unlike other gauges in the market, which gauge will fail in case of internal coil is failing, our gauges are designed to have a backup coil.
- NITROX compatible with Oxygen Cleaned environment, Viton O-Rings on all parts (swivel + HP port) and Christo-Lube lubricant.
- 30% longer phosphorecent effect.
- Color coded indicator with 10-bar increments (pressure) and 1-meter increments (depth)
- Improved swivel umberella design with chanelled o-ring gutter.
- 7/16″ HP port connection.
- We designed an angle for the gauge so it is easy to view while maintaining its shape for durability (in case of drop/shock).